1. Documentation

Host Preparation

If you are using Vagrant to run OpenShift Origin, you do not need to go through the following sections. These changes are only necessary when you are setting up the host yourself. If you are using Vagrant, see the Contributing Guide, then you can skip directly to trying out the sample applications.

Installing Base Packages

For RHEL 7 systems:

  1. Install the following base packages:

    # yum install wget git net-tools bind-utils iptables-services bridge-utils bash-completion kexec sos psacct

  2. Update the system to the latest packages:

    # yum update

For RHEL Atomic Host 7 systems:

  1. Ensure the host is up to date by upgrading to the latest Atomic tree if one is available:

    # atomic host upgrade

  2. After the upgrade is completed and prepared for the next boot, reboot the host:

    # systemctl reboot

Preparing for Advanced Installations

If you plan to use the advanced installation method, you must install Ansible and clone the openshift-ansible repository from GitHub, which provides the required playbooks and configuration files.

For convenience, the following steps are provided if you want to use EPEL as a package source for Ansible:

  1. Install the EPEL repository:

    # yum -y install \
    https://dl.fedoraproject.org/pub/epel/epel-release-latest-7.noarch.rpm

  2. Disable the EPEL repository globally so that it is not accidentally used during later steps of the installation:

    # sed -i -e "s/^enabled=1/enabled=0/" /etc/yum.repos.d/epel.repo

  3. Install the packages for Ansible:

    # yum -y --enablerepo=epel install ansible pyOpenSSL

To clone the openshift-ansible repository:

# cd ~
# git clone https://github.com/openshift/openshift-ansible
# cd openshift-ansible

Be sure to stay on the master branch of the openshift-ansible repository when running an advanced installation.

Installing Docker

At this point, you should install Docker on all master and node hosts. This allows you to configure your Docker storage options before installing OpenShift Origin.

  1. For RHEL 7 systems, install Docker 1.12.

    On RHEL Atomic Host 7 systems, Docker should already be installed, configured, and running by default.

    		 
    # yum install docker

    After the package installation is complete, verify that version 1.12 was installed:

    # docker version

  2. Edit the /etc/sysconfig/docker file and add --insecure-registry 172.30.0.0/16 to the OPTIONS parameter. For example:

    OPTIONS='--selinux-enabled --insecure-registry 172.30.0.0/16'

    If using the Quick Installation method, you can easily script a complete installation from a kickstart or cloud-init setup, change the default configuration file:

    # sed -i '/OPTIONS=.*/c\OPTIONS="--selinux-enabled --insecure-registry 172.30.0.0/16"' \
/etc/sysconfig/docker

    The Advanced Installation method automatically changes /etc/sysconfig/docker.

    The --insecure-registry option instructs the Docker daemon to trust any Docker registry on the indicated subnet, rather than requiring a certificate.

    172.30.0.0/16 is the default value of the servicesSubnet variable in the master-config.yaml file. If this has changed, then the --insecure-registry value in the above step should be adjusted to match, as it is indicating the subnet for the registry to use. Note that the openshift_master_portal_net variable can be set in the Ansible inventory file and used during the advanced installation method to modify the servicesSubnet variable.

    After the initial OpenShift Origin installation is complete, you can choose to secure the integrated Docker registry, which involves adjusting the --insecure-registry option accordingly.

Configuring Docker Storage

Containers and the images they are created from are stored in Docker’s storage back end. This storage is ephemeral and separate from any persistent storage allocated to meet the needs of your applications.

For RHEL Atomic Host

The default storage back end for Docker on RHEL Atomic Host is a thin pool logical volume, which is supported for production environments. You must ensure that enough space is allocated for this volume per the Docker storage requirements mentioned in System Requirements.

If you do not have enough allocated, see Managing Storage with Docker Formatted Containers for details on using docker-storage-setup and basic instructions on storage management in RHEL Atomic Host.

For RHEL

The default storage back end for Docker on RHEL 7 is a thin pool on loopback devices, which is not supported for production use and only appropriate for proof of concept environments. For production environments, you must create a thin pool logical volume and re-configure Docker to use that volume.

You can use the docker-storage-setup script included with Docker to create a thin pool device and configure Docker’s storage driver. This can be done after installing Docker and should be done before creating images or containers. The script reads configuration options from the /etc/sysconfig/docker-storage-setup file and supports three options for creating the logical volume:

  • Option A) Use an additional block device.

  • Option B) Use an existing, specified volume group.

  • Option C) Use the remaining free space from the volume group where your root file system is located.

Option A is the most robust option, however it requires adding an additional block device to your host before configuring Docker storage. Options B and C both require leaving free space available when provisioning your host.

  1. Create the docker-pool volume using one of the following three options:

    • Option A) Use an additional block device.

      In /etc/sysconfig/docker-storage-setup, set DEVS to the path of the block device you wish to use. Set VG to the volume group name you wish to create; docker-vg is a reasonable choice. For example:

      # cat <<EOF > /etc/sysconfig/docker-storage-setup
DEVS=/dev/vdc
VG=docker-vg
EOF

      Then run docker-storage-setup and review the output to ensure the docker-pool volume was created:

      # docker-storage-setup                                                                                                                                                                                                                                [5/1868]
0
Checking that no-one is using this disk right now ...
OK

Disk /dev/vdc: 31207 cylinders, 16 heads, 63 sectors/track
sfdisk:  /dev/vdc: unrecognized partition table type

Old situation:
sfdisk: No partitions found

New situation:
Units: sectors of 512 bytes, counting from 0

   Device Boot    Start       End   #sectors  Id  System
/dev/vdc1          2048  31457279   31455232  8e  Linux LVM
/dev/vdc2             0         -          0   0  Empty
/dev/vdc3             0         -          0   0  Empty
/dev/vdc4             0         -          0   0  Empty
Warning: partition 1 does not start at a cylinder boundary
Warning: partition 1 does not end at a cylinder boundary
Warning: no primary partition is marked bootable (active)
This does not matter for LILO, but the DOS MBR will not boot this disk.
Successfully wrote the new partition table

Re-reading the partition table ...

If you created or changed a DOS partition, /dev/foo7, say, then use dd(1)
to zero the first 512 bytes:  dd if=/dev/zero of=/dev/foo7 bs=512 count=1
(See fdisk(8).)
  Physical volume "/dev/vdc1" successfully created
  Volume group "docker-vg" successfully created
  Rounding up size to full physical extent 16.00 MiB
  Logical volume "docker-poolmeta" created.
  Logical volume "docker-pool" created.
  WARNING: Converting logical volume docker-vg/docker-pool and docker-vg/docker-poolmeta to pool's data and metadata volumes.
  THIS WILL DESTROY CONTENT OF LOGICAL VOLUME (filesystem etc.)
  Converted docker-vg/docker-pool to thin pool.
  Logical volume "docker-pool" changed.

    • Option B) Use an existing, specified volume group.

      In /etc/sysconfig/docker-storage-setup, set VG to the desired volume group. For example:

      # cat <<EOF > /etc/sysconfig/docker-storage-setup
VG=docker-vg
EOF

      Then run docker-storage-setup and review the output to ensure the docker-pool volume was created:

      # docker-storage-setup
  Rounding up size to full physical extent 16.00 MiB
  Logical volume "docker-poolmeta" created.
  Logical volume "docker-pool" created.
  WARNING: Converting logical volume docker-vg/docker-pool and docker-vg/docker-poolmeta to pool's data and metadata volumes.
  THIS WILL DESTROY CONTENT OF LOGICAL VOLUME (filesystem etc.)
  Converted docker-vg/docker-pool to thin pool.
  Logical volume "docker-pool" changed.

    • Option C) Use the remaining free space from the volume group where your root file system is located.

      Verify that the volume group where your root file system resides has the desired free space, then run docker-storage-setup and review the output to ensure the docker-pool volume was created:

      # docker-storage-setup
  Rounding up size to full physical extent 32.00 MiB
  Logical volume "docker-poolmeta" created.
  Logical volume "docker-pool" created.
  WARNING: Converting logical volume rhel/docker-pool and rhel/docker-poolmeta to pool's data and metadata volumes.
  THIS WILL DESTROY CONTENT OF LOGICAL VOLUME (filesystem etc.)
  Converted rhel/docker-pool to thin pool.
  Logical volume "docker-pool" changed.

  2. Verify your configuration. You should have a dm.thinpooldev value in the /etc/sysconfig/docker-storage file and a docker-pool logical volume:

    # cat /etc/sysconfig/docker-storage
DOCKER_STORAGE_OPTIONS=--storage-opt dm.fs=xfs --storage-opt
dm.thinpooldev=/dev/mapper/docker--vg-docker--pool

# lvs
  LV          VG   Attr       LSize  Pool Origin Data%  Meta%  Move Log Cpy%Sync Convert
  docker-pool rhel twi-a-t---  9.29g             0.00   0.12

    Before using Docker or OpenShift Origin, verify that the docker-pool logical volume is large enough to meet your needs. The docker-pool volume should be 60% of the available volume group and will grow to fill the volume group via LVM monitoring.

  3. Check if Docker is running:

    # systemctl is-active docker

  4. If Docker has not yet been started on the host, enable and start the service:

    # systemctl enable docker
# systemctl start docker

    If Docker is already running, re-initialize Docker:

    This will destroy any containers or images currently on the host.

    		 
    # systemctl stop docker
# rm -rf /var/lib/docker/*
# systemctl restart docker

    If there is any content in /var/lib/docker/, it must be deleted. Files will be present if Docker has been used prior to the installation of OpenShift Origin.

Reconfiguring Docker Storage

Should you need to reconfigure Docker storage after having created the docker-pool, you should first remove the docker-pool logical volume. If you are using a dedicated volume group, you should also remove the volume group and any associated physical volumes before reconfiguring docker-storage-setup according to the instructions above.

See Logical Volume Manager Administration for more detailed information on LVM management.

Managing Container Logs

Sometimes a container’s log file (the /var/lib/docker/containers/<hash>/<hash>-json.log file on the node where the container is running) can increase to a problematic size. You can manage this by configuring Docker’s json-file logging driver to restrict the size and number of log files.

Aggregated logging is only supported using the journald driver in Docker. See Updating Fluentd’s Log Source After a Docker Log Driver Update for more information.
Option Purpose

--log-opt max-size

Sets the size at which a new log file is created.

--log-opt max-file

Sets the file on each host to configure the options.

For example, to set the maximum file size to 1MB and always keep the last three log files, edit the /etc/sysconfig/docker file to configure max-size=1M and max-file=3:

OPTIONS='--insecure-registry=172.30.0.0/16 --selinux-enabled --log-opt max-size=1M --log-opt max-file=3'

Next, restart the Docker service:

# systemctl restart docker

Viewing Available Container Logs

Container logs are stored in the /var/lib/docker/containers/<hash>/ directory on the node where the container is running. For example:

# ls -lh /var/lib/docker/containers/f088349cceac173305d3e2c2e4790051799efe363842fdab5732f51f5b001fd8/
total 2.6M
-rw-r--r--. 1 root root 5.6K Nov 24 00:12 config.json
-rw-r--r--. 1 root root 649K Nov 24 00:15 f088349cceac173305d3e2c2e4790051799efe363842fdab5732f51f5b001fd8-json.log
-rw-r--r--. 1 root root 977K Nov 24 00:15 f088349cceac173305d3e2c2e4790051799efe363842fdab5732f51f5b001fd8-json.log.1
-rw-r--r--. 1 root root 977K Nov 24 00:15 f088349cceac173305d3e2c2e4790051799efe363842fdab5732f51f5b001fd8-json.log.2
-rw-r--r--. 1 root root 1.3K Nov 24 00:12 hostconfig.json
drwx------. 2 root root    6 Nov 24 00:12 secrets

See Docker’s documentation for additional information on how to Configure Logging Drivers.

Ensuring Host Access

The advanced installation method requires a user that has access to all hosts. If you want to run the installer as a non-root user, passwordless sudo rights must be configured on each destination host.

For example, you can generate an SSH key on the host where you will invoke the installation process:

# ssh-keygen

Do not use a password.

An easy way to distribute your SSH keys is by using a bash loop:

# for host in master.example.com \
    node1.example.com \
    node2.example.com; \
    do ssh-copy-id -i ~/.ssh/id_rsa.pub $host; \
    done

Modify the host names in the above command according to your configuration.

What’s Next?

If you are interested in installing OpenShift Origin using the containerized method (optional for Fedora, CentOS, or RHEL but required for RHEL Atomic Host), see Installing on Containerized Hosts to prepare your hosts.

If you came here from Getting Started for Administrators, you can now continue there by choosing an installation method. Alternatively, you can install OpenShift Origin using the advanced installation method.

If you are installing a stand-alone registry, continue with Installing a Stand-alone Registry.